Weller wd2m manual

In addition to this, the displayed channel is indicated by a red LED next to the connection socket. The " " symbol and the green LED on the connection socket are used as a visual control check. The active channel in the display is indicated with an arrow underneath it. In addition to this, the displayed channel is indicated by a red LED over the connection socket.

The display then switches back automatically to the The displayed channel can be switched off by simultaneously pressing the UP and DOWN buttons 2 3. This is confirmed in the display with OFF. To activate a deactivated channel, select it using the channel selection button, if necessary, and simultaneously press the UP and DOWN buttons 2 3 to switch it on.

The actual value appears in the display. While the button is depressed, the small display assigned to the Radio Button also flashes and, after 3 seconds, accepts the value of the large display. Release the Radio Button. Radio Button 2 is used to exit the menu. The soldering station is now reset to its factory default settings.

Special functions menu 2: Calibration function, Remote Id 4 sec. Menu Selection 7. Switch to the previous menu item with Radio Button 1. The Auto Off time can be set from 0 — minutes. With a setting of "0 min", the Auto Off function is disabled. Auto Off is carried out independently of the Setback function.

Switch to previous menu item with Radio Button 1. The Setback time, after which the soldering unit switches to Standby mode, can be set from 0 — 99 minutes. With a setting of "0 min", the Setback function is switched Off. The Offset function is used to match the station display to the tip temperature when measured with an external instrument.

The Locked temperature thus represents the middle of the settable temperature range. Note: To utilize the window function, the station has to first be placed into Lock mode. Confirm the code by depressing Radio Button 2 for 5 seconds. Enter Functions menu 1. The station is now unlocked. The station is now reset to its factory default settings. Important: The soldering tool becomes hot during the Factory Control Check. Never leave combustible materials near the hot soldering iron.

Once the temperature becomes stable at which point the indicator flashes , the soldering tip temperature reading on the external device is compared to that shown on the station display. The temperature Offset is indicated in the display.

Press Radio Button 2 to exit the menu without saving 8 any changes. The temperature offset is indicated in the display. The temperature offset is reset to 0. Press Radio Button 2 to exit the menu without saving any changes. Never apply mechanical force to the soldering tip. This software contains a firmware updater and monitor software. The monitor software can be used for remote control of the unit. Temperature curves can be displayed, printed out and saved.

Accessories WMP 9. Operating Guidelines During initial heat-up, tin the soldering tip with solder to remove oxidation and contamination on the soldering tip. Before placing tool in holder, be sure the soldering tip is well tinned.

Use of an aggressive flux will shorten tip life. Dirt or foreign materials could cause damage and could affect tip temperature accuracy. Rule of thumb: approximately as large as the soldering pad.

Where necessary, use the appropriate tool to change the soldering tips. The ergonomic anti-static design, the quick-change plug-in micro-soldering tips, extremely fast tool heat up, and an auto-off feature when placed in the tool holder, provide the superior performance, versatility, and quality established by Weller.

Cautions and Warnings! Warning: This product, when used for soldering and similar applications, produces chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

There is a risk of burns from molten solder. Description An extremely powerful 40 W fine soldering iron with the heating system integrated into the soldering tip. When the tool reaches the set temperature, tin the soldering tip with solder. Operating Information Changing the soldering tip Caution, risk of burns! Soldering tips must only be changed when cool. The tip change does not require tools. The soldering tip is removed by simply grasping the soft grip of the soldering tip and pulling from the tool.

A tip is inserted by pushing the plug end of the tip into the front end receptacle of the hand piece. Important: Always ensure that the soldering tip is properly seated. When installing a new soldering tip, ensure that the soldering tip is inserted completely up to the stop in a single motion. Operation with a soldering tip that is not completely inserted can cause the tip to malfunction.

During initial heat-up, tin the soldering tip with solder. This removes oxide layers and contamination on the soldering tip. Before placing the tool in the holder, always ensure the soldering tip is well tinned. The use of an aggressive flux may shorten tip life. Always keep the cleaning sponge 4 damp. Use only distilled or de-ionized water. In addition to the informaton included in this manual, please see the safety manual and the instructions for the applicable power unit.

Subject to technical change without notice! Placing into Operation Place the soldering iron in the WMRH tool stand and ensure that the soldering iron grip is correctly seated against the tool holder 1. Move all combustible objects away from the soldering iron and the work area. The ergonomic anti-static design, selection of desoldering tweezer tips, and 80 watts of power, provide Weller superior performance, versatility, and quality.

There is a risk of burns associated with molten solder. Placing into Operation the stand 1. Move all combustible objects away from the tweezers and the work area. Insert the connector 5 into the power supply receptacle and lock it by turning clockwise.

When the tips have reached the set temperature, tin both tweezer tips with solder. Desoldering tips must only be changed when cool. The desoldering tip cartridge is inserted into the front of the hand piece 4.

The 5-pin mini-plug on the back of the tip cartridge is polarized for correct alignment with the hand piece. The top of the tip cartridge is printed with L Left and R Right indicators for proper orientation. The indicators align with L and R indicators printed on the hand piece. The tip cartridge 3 can be removed from the hand piece by grasping the molded grips and pulling outward to release.

Important: Always ensure that the desoldering tip is properly seated. When installing a new desoldering tip cartridge, ensure that the cartridge is inserted completely against the stop in a single motion. Operation with a desoldering tip that is not completely inserted can cause the tip cartridge to malfunction.

During initial heat up, tin the tips with solder. This removes oxidation and contamination on the desoldering tips. Before placing the tool in the holder, always ensure that the desoldering tips are well tinned. Get this manual by email Other manuals of this product.

Need help? Post your question in this forum. Report abuse Libble takes abuse of its services very seriously. Product: Spam. Hateful or violent content For example, Anti-Semitic content, racist content, or material that could result in a violent physical act. Personal or private information For example, a credit card number, a personal identification number, or an unlisted home address.

Promotion of regulated goods and services. Forumrules To achieve meaningful questions, we apply the following rules: First, read the manual; Check if your question has been asked previously; Try to ask your question as clearly as possible; Did you already try to solve the problem?

Therefore, avoid filling in personal details. Register Register getting emails for Weller WD2M at: new questions and answers new manuals You will receive an email to register for one or both of the options. The manual is 6,1 mb in size. The manual is sent by email. Check your email If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.